View The EZ Square Bandsaw Fence Installation Inructions

Re-engineered
switchable hold down
magnets!

The MAGFENCE II™ Universal Magnetic Fence is the fastest, easiest way to add a moveable and adjustable fence to your bandsaw. Since the MAGFENCE II™ attaches to your saw with switchable magnets, it is readily adjusted and infinitely positionable. You don't even need any hardware or mounts when installing. Simply place in position and switch the magnets to the ON position and you are set. The fence has thin rubber strips on the bottom to make adjustments smooth and simple, they also keep the fence from scratching your table top surface. The unit also features multiple T-slots for attaching any number of accessories like a sub-fence, stops and is compatible with all of Carter's original MAGFENCE™ accessories. The MAGFENCE II™ comes with two switchable magnets and measures 15" in length by 3" in height. Additional switchable magnets (sold separately) can be added to the fence for even more holding power

Cut your own wood, veneer
or even bowl blanks with the
Carter Log Mill™

The Carter AccuRight™ Circle Cutting Jig quickly and easily attaches to almost any saw, allowing you to cut perfect circles every time. The Carter AccuRight™ Circle Cutting Jig allows you to cut any diameter circle up to four feet, when used with proper external support.

• Features:
• Attaches quickly and easily with Carter MAGFENCE™ (optional extra) (See Above)
• Can be used without the MAGFENCE™ with the included universal attachment bracket
• Allows cutting of circles up to 4+ Feet diameter with proper external support (user provided)
• No drilling or external mounts necessary
• Easy to read radius measurements for precise circle size
• Circle thickness only limited by the saw’s resaw capacity
• Installs and removes quickly for limited downtime
• Compatible with any size Carter MAGFENCE™
• For use with any blade guide, full block or bearing, (not for use with the Stabilizer™).

The AccuRight® Center Master™ Blank Creation System makes it possible to easily and consistently cut and mount circular lathe blanks (for bowl turning, hollow form projects, etc.) using the Carter Circle Cutter (sold separately above ). The device allows even thick pieces of wood to be cut into round blanks and makes it possible to mount these blanks precisely centered onto a lathe faceplate, thus minimizing vibration and getting your project off to a quick and safe start. Precisely cutting the blank also allows you to keep scrap to a minimum and use larger scraps of valuable wood for additional projects. The ACCURIGHT® Center Master consists of two parts: a wide sliding pivot plate for use with the ACCURIGHT® Circle Cutter (sold separately); and the Center Master™ faceplate adaptor mounting jig to ensure perfect centering of the finished blank. The Center Master™ is thread specific so make sure you order the correct size for your faceplate.

Our bandsaw tension spring replacement provides, superior strength, excellent durability. The coil assists will assist you in properly tensioning larger blades and to give superior tracking over the stock spring that comes with most saws. The tensioning spring will fit most 14" band saws.

This 75 Watt (maximum) magnetic base light holds firmly to most any machine and has three fully functional joint, plus a fourth joint that rotates the lamp 360°.

• 3 prong U.L approved 18 gauge 5 ft. long cord and plug
• light bulb not included
  

The Limber Light™ is a small cable free LED task light with a magnetic base. This light can be placed anywhere you need additional work light for your tools. The Limber Light™ comes with batteries pre-installed and as a bonus the next battery change is on us as we include extra batteries with every unit.

For improved finish and blade performance. Lay the side of the wood handle on the table surface and place the silicon carbide stone against the back of the blade to round off the edges and correct any weld misalignment. No lubricant needed.

Blade Finishing Stone Advantages: permits tighter radius cutting, smooths off uneven welds, prevents excessive wear on thrust bearings, provides a smoother finish on the workpiece during radius cutting and removes mushrooming on back of blade caused by pressure against thrust bearings.

Our snap into place inserts rplace your old beat-up throat plate insert. These inserts are absolutely perfect
for scrollwork, small or fragile parts, tiny or small projects, and woods that are prone to splintering or changing,these band saw inserts provide a solid work base for your work piece and will not dull your saw teeth on your band saw blade. Easy to install in just seconds.

(Three inserts per pack).

Carter AccuRight Zero Clearance bandsaw table inserts. Nylon material saves blade in case of accidental contact. Tighter blade opening results in less chipping and rough edges when cutting thin material.

3 Inserts per package.

The Clean sweep™ helps keep your tires free from debris which shorten their life and effect blade tracking. As debris; saw dust, metal on metalworking saws, or any other debris accumulates on the tire, continued use without cleaning compresses the tire more in other places then if it were in contact with the rubber or urethane alone. Over time the tire will loose its rebound in those places if not cleaned properly and thus decrease tire life. (Currently only offered for 14" saws)

15 amp Heavy Duty Foot Switch
This switch works only when it is held
down with foot presure.

5 amp Heavy Duty Foot Switch
This switch works as a on / off switch.
Foot presure down turns the switch on, with second foot presure turning the switch off.